Most Common Taurus Model 65 Problems and Their Solutions
The Taurus Model 65 is a revolver designed by Taurus. It comes with a rubber grip and fixed sights. But, there are a few issues with the revolver that you should know before buying one.
Cylinder not rotating, gas spitting, shooting low and towards the right, difficulty pulling the trigger, and accuracy issues are some of the most common Taurus Model 65 problems.
Features & Specifications of Taurus Model 65:
| Caliber | 357 Mag, 38 Special +P |
| Capacity | 6 Rounds |
| Barrel Length | 4.0 Inches |
| Weight (Unloaded) | 38.0 Ounces |
| Length | 10.50 Inches |
| Width | 1.50 Inches |
| Height | 5.50 Inches |
| Action Type | DA/SA |
| Safety | Transfer Bar Safety, Taurus Security System |
| Sights | Fixed front and rear sights |
Common Taurus Model 65 Problems and Solutions
| Problems with Taurus Model 65 | Solutions |
| Cylinder Doesn’t Rotate | Disassemble and inspect the cylinder mechanism. Use a gun cleaner. |
| Spitting Gas | Ensure O-rings, magazine, and valve are in good condition. |
| Frequently Shooting Low and Right | Maintain a proper grip. Practice consistent trigger control. |
| Hard to Pull the Trigger | Apply an appropriate firearm lubricant to the trigger mechanism, Replace broken trigger return springs. |
| Accuracy Issues | Check for damage or obstructions in the barrel’s crown and rifling. |
1. Cylinder Doesn’t Rotate:
Numerous complaints have been made regarding the Taurus Model 65. The most prevalent one is that the cylinder on certain versions occasionally does not rotate.
The revolver will ultimately stop firing sometimes. Additionally, the revolver will discharge incorrectly, causing the bullet to exit the barrel at an angle. It can be incorrect and hazardous.
The problem might at times jam the revolver, making it hard to shoot or clear.
The Fix:
It’s crucial to put down your Taurus Model 65 immediately if you discover that the cylinder cannot rotate correctly.
You must disassemble the revolver to check the cylinder mechanism for dirt, wear and tear, breakage, or other issues.
The cylinder mechanism is capable of being checked for wear and tear or damage once the revolver has been dismantled.
Use a gun cleaner and a soft brush to remove any dirt you detect. You will need to replace any worn-out or broken components you uncover.
2. Spitting Gas:
The Taurus Model 65 spitting gas problem occurs when the gun leaks gas when it is fired from the barrel or other components of the revolver. There are numerous potential causes for this.
If the O-rings are worn out or damaged, they can cause gas to leak. Gas can occasionally leak out of a magazine that is broken or damaged. The gas may accumulate and eventually seep out if the barrel is contaminated.
Additionally, the valve is in charge of regulating the flow of gas into the gun; if it is worn out or damaged, gas may leak out.
The Fix:
Check the cylinder, barrel, and forcing cone of the handgun carefully for any obvious signs of damage. Harm in these places may cause gas to spit.
The distance between the front face of the cylinder and the back of the barrel is called a factory-loaded cylinder gap. You should measure it. For the suggested gap measurements, read your owner’s manual.
The type of powder used in some ammunition or other reasons may make it more likely to cause gas spitting. You should utilize top-notch ammo that has been factory-loaded can lessen this problem.
3. Frequently Shooting Low and Right:
Uneven pressure or the wrong grip can result in irregular shot placement. The barrel may dip low and to the right during the shot if the trigger control is poor. This happens in the case of jerking or flinching.
Shots can occasionally miss their target if the front and rear sights are not aligned properly. Shot placement may be impacted by an unstable shooting stance or poor recoil management.
The Fix:
Make certain that you have a secure grip on the gun. Your body should be correctly aligned with the target.
To improve your trigger control, you should practice dry-fire shooting with an unloaded gun.
Double-check that your front and back sights are properly adjusted. Also, make sure you keep a constant sight picture throughout every shot.
Make sure you consistently use the same reference point for every shot if you use a reference point on the target.
4. Hard to Pull the Trigger:
Heavy trigger pulls may occur if the trigger return spring is broken. It may be difficult to cock the hammer. It results in a strong trigger pull if the hammer spring is weak or worn.
The inappropriate type of lubricant used might lead to an accumulation of muck in the trigger mechanism. This increases friction and makes the trigger pull heavier.
Internal components, such as the trigger and hammer, may become misaligned.
The Fix:
Verify that the revolver is not loaded and that there is no live ammunition nearby. Disassemble the revolver and pay attention to the trigger mechanisms.
Use a proper firearm cleaning solution and brushes to thoroughly clean all trigger components. Clean the trigger, hammer, and their related springs.
You should ensure that there is no debris that could be producing friction. After cleaning, lightly cover the trigger mechanism with a lubricant designed for use with firearms.
5. Accuracy Issues:
Accuracy problems with a Taurus Model 65s are not unusual. Accuracy issues can result from inconsistent grip or stance.
Due to bullet weight, velocity, and powder charge, various types and brands of ammunition can result in varied points of contact.
Accuracy depends on using ammo that performs well with your particular handgun.
The Fix:
Try out various types and brands of ammo to determine which one works best with your Taurus Model 65.
Make sure the ammo you select is suitable for the purpose for which it will be used.
Maintain your Taurus Model 65 regularly. You should give close attention to the barrel and chamber. Check the crown and rifling of the barrel for any damage or obstruction.
Read Also: Glock 42 vs SIG P365: Comparing the Micro-Compact Pistols
User Feedback on Taurus Model 65
The Taurus Model 65 has received both good and bad reviews. It is a reliable gun. But, it faces some common problems that almost every other revolver has.
In a post in the 1911 Forum, you can see that the owners of the Taurus Model 65 love the gun. In this YouTube video, you can see how it performs in the range.
In this post in Taurus Armed, one user said that his cylinder had a problem with rotating. He also faced an issue with the trigger. The trigger refused to pull back.
Top 3 Alternative Guns of Taurus Model 65
Here are the best alternatives for the Taurus Model 65:
- Smith & Wesson Model 686
– It is a single-action/double-action revolver with a 4.13-inch barrel.
– The magazine has a capacity of 6 supporting 357 magnums.
– Features an L-frame with stainless steel barrel and frame. - Colt Python
– Has a firing range of 200 or more yards.
– Colt Python is a double-action revolver that shoots .357 and .38 rounds.
– Comes with a 3-3.99 inches stainless steel barrel. - Kimber K6S
– Kimber K6S is a double-action-only revolver.
– Comes with a 2-inch stainless steel barrel and brushed stainless finish.
– Features white 3-dot sights with a 4.1-inch radius.
Frequently Asked Questions [FAQs]
What is the twist rate of the Taurus Model 65?
The Taurus Model 65 has a twist rate of 1:16.5 in RH twist.
What kind of materials is used in the Taurus Model 65?
The Taurus Model 65 comes with a stainless steel frame, material, and barrel.
What is the frame size of the Taurus Model 65?
A medium size frame is used in the Taurus Model 65.
Does the Taurus Model 65 have different barrel lengths?
Yes, it has 2, 4, and 6-inch options.
Can the Taurus Model 65 be hidden?
The 2-inch model can be hidden with ease. But, the other models may be harder to conceal.
